Terug naar blog
Handleidingen 2026-11-16 Groomer's Warehouse 0 weergaven

Groomer's Warehouse 7" 18 Tooth Chunker Shear: How to Use It

Groomer's Warehouse 7" 18 Tooth Chunker Shear: How to Use It

Learn when an 18 tooth chunker shear earns its place in dog grooming, how to remove bulk coat with control, and what the GW-18 Tooth Chunker Shear offers.

What an 18 Tooth Chunker Shear Does in a Grooming Routine

A chunker shear is a bulk-removal tool. Instead of a clean, full-length cut, its toothed edge takes out sections of coat, which makes it useful when you need to reduce weight and volume before finishing with a smoother shear or clipper work. The 18 tooth configuration sits in the middle of the chunker range, giving you a balance between how much coat each pass removes and how much control you keep over the shape.

That middle ground is why a dog grooming chunker shear is often reached for on thicker or longer coats that need to be brought down before detail work. It is not a finishing shear, and it is not a substitute for a clipper on a short trim. Think of it as the step that makes the next step easier.

What the GW-18 Tooth Chunker Shear Brings to the Table

  • Groomer's Warehouse 7" 18 Tooth Chunker Shear: Crafted from Japanese 440C stainless steel, the GW-18 Tooth Chunker Shear boasts high quality and durability. Steel choice is the foundation of how a shear holds its edge and feels in the hand during repeated bulk-removal passes.
    Groomer's Warehouse 7" 18 Tooth Chunker Shear
    Groomer's Warehouse 7" 18 Tooth Chunker Shear
  • Groomer's Warehouse 7" 18 Tooth Chunker Shear: Featuring an offset ergonomic handle and adjustable gemstone tension knob, this 7" inch shear offers precision and comfort. The offset handle and tension knob are the two features you will interact with most while learning chunker shear technique.
  • Groomer's Warehouse 7" 18 Tooth Chunker Shear: Enjoy the added benefit of a permanent finger rest. A permanent finger rest gives your little finger a consistent anchor point, which helps steady the shear during controlled, repeated cuts.

How to Use a Chunker Shear to Remove Bulk Dog Coat

The sequence below is built around the tool's design, not a fixed grooming standard. Work at a pace that lets you see each section before you move on.

  1. Start on a clean, dry or properly prepared coat: Bulk removal is easier to judge when the coat is not tangled or weighed down. Work through any mats first with the appropriate tool before introducing a chunker.
  2. Set the tension knob before your first cut: The adjustable gemstone tension knob lets you tune how the blades close. Check that the shear opens and closes smoothly and that the tension feels consistent across a few test snips in the air.
  3. Anchor your hand with the permanent finger rest: Rest your little finger on the permanent finger rest and let the offset handle sit naturally in your palm. A stable grip is what keeps chunker cuts even.
  4. Section the coat and work in small passes: Divide the coat into manageable sections. Take small, deliberate cuts rather than long closures, and check the silhouette after each pass before removing more.
  5. Blend toward the finish: Chunker cuts are meant to be blended. Once the bulk is reduced, move to your finishing shear or clipper work to smooth the transitions.

Chunker Shear Technique Checkpoints

  • Watch the coat, not the blades: Keep your eyes on the shape you are building. The toothed edge removes coat in a pattern, so checking the outline after each pass prevents over-removal.
  • Keep passes consistent: Even pressure and even spacing between cuts give you a more predictable result than rushing through a section.
  • Re-check tension as you work: The adjustable gemstone tension knob is there to be used. If the shear starts to feel loose or tight mid-session, stop and adjust before continuing.
  • Stop before you think you need to: Bulk removal is hard to undo. Leaving a little extra coat gives you room to refine with a finishing tool.

When the 18 Tooth Chunker Shear Is the Right Reach

Choose an 18 tooth chunker shear when the coat has enough length and density that removing bulk will meaningfully shorten your finishing time, but you still want visible control over the shape. It suits groomers who are comfortable sectioning a coat and checking their work as they go.

It is less suited to very short coats, where there is little bulk to remove, or to situations that call for a clean, uniform finish from the first cut. In those cases a different shear or clipper setup is the better starting point.

What the Supplied Information Does Not Cover

The available product record confirms the steel, handle style, tension knob, finger rest, and the 7" size. It does not include care instructions, sharpening guidance, or species-specific usage notes. Treat those as decisions to confirm with the manufacturer or your sharpener rather than assumptions. If you need documented care steps before buying, ask before you order.

Gerelateerde artikelen

Customer Service
Home
Producten
Winkelwagen
Profiel